A lithophane is only half a project. The print encodes the image in thickness, but what you actually see is light that made it through, and that light decides whether the picture appears or the panel looks like grey plastic.
Three things matter more than the print: how far the light sits behind the panel, whether that light is diffused, and what colour it is. Get those right and even a mediocre print looks good.
Why a bare LED ruins it
A single point of light behind a panel produces a bright centre and dark edges. The panel is transmitting light from a source only a few millimetres away, and brightness falls off with distance, so the image gets a grey-to-black gradient across it that has nothing to do with the photo.
Diffusion fixes this. It is the difference between shining a torch at the panel and putting the panel against an overcast sky.
The three numbers
| Number | Value | Why |
|---|---|---|
| Panel to light distance | 10–30 mm | Closer gives a hot spot; further washes out |
| Diffuser gap in front of the LEDs | 5–10 mm | Lets the light mix before it reaches the print |
| Colour temperature | 2700–3000 K for portraits, 5000 K for detail | Warm flatters skin; cool reveals texture |
If you can only remember one: 20 mm and a diffuser. That combination is forgiving of everything else.
Parts that work
- LED strip, 8 mm wide, 5 V or 12 V. A COB strip gives a continuous line of light with no visible dots, which is exactly what a lithophane wants. About 1 W is plenty for a 100 × 150 mm panel; 30–60 LEDs per metre is enough.
- A diffuser. 2–3 mm opal acrylic is the proper material. White baking paper works for a first build. A printed 0.8 mm white PLA sheet also diffuses surprisingly well — print it at 100% infill.
- A frame with depth. A cheap A6 photo frame with 15–20 mm of internal depth does the job, and it already has the opening cut for the panel.
- An inline switch or a small dimmer. À dimmer matters more than brightness: a lithophane that is too bright loses mid-tones and looks like a light bulb.
Build order
- Size the print to your frame opening, not the other way round. A 100 × 150 mm panel fits most A6 frames with a few millimetres to grip.
- Mount the strip around the inside of the frame's back, not in the middle — perimeter mounting plus diffusion gives even light with less hotspotting.
- Put the diffuser 5–10 mm in front of the LEDs.
- Leave 10–20 mm between the diffuser and the print.
- Check it before closing the frame: hold the panel in front of the light at arm's length and look for bright patches. If you can see the LEDs through the print, the diffusion gap is too small.
Total depth needed for a small panel: about 30 mm. Most people end up 3D-printing a shallow box instead of finding a frame that deep, which is fine — 2 mm walls, a 4 mm slot for the diffuser and a 3 mm ledge for the lithophane is all the geometry you need.
What to avoid
- Bare LEDs or a phone torch as the permanent light. Fine for a five-second test, not a display.
- Coloured or RGB light. A blue-lit portrait looks like a mistake; colour fights the image.
- Glass directly in front of the panel. It reflects the room and doubles the image, which looks like a printing error.
- High-power strips without a dimmer. Too much light flattens the contrast range that the print worked for.
- Sealing the box airtight around a 12 V strip. It does not get hot enough to be dangerous, but leaving a small vent avoids slow yellowing of the plastic.
The test that saves an evening
Before you build anything, hold the finished panel against a phone screen set to a plain white image at medium brightness, 20 mm away. That is roughly what the LED build will give you. If the picture reads at that distance, it will read in the frame. If it looks flat and grey, the problem is the print — usually too thick a panel or a filament that is not white enough, which the filament guide covers.
Making it a proper night light
For something in a bedroom rather than on a shelf, two changes matter: drop the brightness to its lowest usable setting so it does not glow like a sign, and use 2700 K. A 5 V USB strip with a small dimmer is easier to live with than a 12 V build with a wall supply, and it can run from any phone charger.
If you want a photo you love as the insert, convert it at the panel size with the lithophane maker — the thickness range of 2.5–4 mm is what makes the backlit version readable.