Image to STL Online

Lithophane preset · dark prints thick

Lithophane Maker

Turn a photo into a 3D-printable lithophane in your browser: dark prints thick, bright prints thin, so the picture shows up when you backlight it.

  • Dark pixels print thick, bright pixels thin — the image appears when backlit
  • Set minimum thickness and maximum height for your own filament
  • Stand it up in the slicer and print it in white PLA at 0.08 mm layers
PNG, JPG, WebP or SVG · up to 15 MB · or drop it here No image loaded

Load an image and the 3D preview shows up here. Drag to rotate, scroll to zoom.

—

Files stay on your device — nothing is uploaded, no account needed.

What a lithophane is

A lithophane is a photo printed as thickness. Where the picture is dark, the plastic is thick and blocks light; where it is bright, the plastic is thin and lets light through. Hold it against a lamp and the image appears — no ink, no paint, just geometry.

This maker turns your photo into that geometry in the browser: dark pixels become the thick end of the range, bright pixels the thin end, and the mesh is closed with a flat back so it prints as one solid piece.

How thick should a lithophane be

Thickness is the whole image. Two numbers matter:

Start with a 1.2 mm base and 3 mm of relief, print one small test at 60 mm wide, hold it to a lamp and adjust from there. Every filament diffuses light differently, so the test print on your own white spool is worth more than any recipe.

Step by step

  1. Pick the photo. Faces and pets work best. High contrast, a plain background and a subject that fills the frame all help — a lithophane has no colour, only brightness.
  2. Crop tight. Every millimetre of empty background is plastic that shows nothing.
  3. Set width, base thickness and max height in the panel above. Leave detail at 200 px unless the picture carries fine texture.
  4. Download the STL and open it in your slicer.
  5. Stand it up. Rotate the model 90° so it prints vertically, add a brim, and never lay it flat — flat lithophanes lose the fine height differences and show layer lines across the face.
  6. Print slow and thin. 0.08–0.12 mm layers, 100% infill, outer wall speed around 20–30 mm/s, white or natural PLA.

Filament and light

White PLA is the default because it diffuses evenly. Natural and clear filaments give a softer, dimmer image; coloured filament tints the whole picture. Matte white hides layer lines better than silk or glossy.

For a night light, print a frame or a slot base and put a warm white LED strip behind it, 20–30 mm away from the surface. Distance matters more than brightness: an LED pressed against the plastic creates a hot spot instead of an image.

Lithophane vs relief

The same converter does both. A relief raises bright pixels instead of thinning them, so you see the picture in normal light and can print it as a plaque or keychain. A lithophane inverts that and only reveals the image when backlit. If your print came out as a negative, the invert checkbox fixes it without starting over.

Privacy

The photo is read, converted and download in your own browser. It is never uploaded, stored or sent anywhere, so family photos and client work stay on your machine.

Questions

Common questions

What makes a good lithophane photo?

A bright, high-contrast picture with the subject filling the frame. Faces, pets and buildings with strong shapes print well; flat, hazy or busy backgrounds lose detail.

How thick should a lithophane be?

A 1.2 mm base with 2–3.5 mm of relief across a 100 mm wide print is a safe starting point. Print a 60 mm test piece and adjust the base upward if bright areas glow too much.

Why print a lithophane vertically?

The height differences are fractions of a millimetre. Printed flat, layer lines cut across the image and the surface scatters light; printed standing up, the layers run along the picture and stay invisible.

Which filament should I use?

White PLA. Matte white diffuses light most evenly; natural or clear filament gives a dimmer, softer image, and coloured filament tints the whole photo.

Can I use a PNG or a JPG?

Both, plus WebP and SVG, up to 15 MB. Transparent areas in a PNG are flattened onto white, which makes them the thin end of the range.

Does it work without a backlight?

No. A lithophane is meant to be lit from behind. If you want a print that shows the picture under normal light, switch the mode to relief instead.