Image to STL Online

Turning a Logo or Text Into an STL You Can Actually Print

Logos need sharp edges and a flat base, not photographic gradients. Which source file to start from, how thin lettering can get, and when extrusion beats relief.

A logo is a different kind of image from a photo, and that changes the whole workflow. Photographs are continuous tone; logos and lettering are flat colour with hard edges. If you run one through a photo converter you get soft, slightly melted edges — printable, but not something you would hand to a client.

Start with the sharpest source you have

The source file decides the result more than any setting. In order of quality:

  1. SVG or other vector — mathematically defined edges, infinitely sharp. Use SVG to STL.
  2. PNG with transparency — clean edges and no background to remove. Use PNG to STL.
  3. PNG or JPG without transparency — works, but you must deal with the background.
  4. A JPG screenshot of a logo — last resort. JPEG compression leaves grey halos around every edge, and those halos become real geometry at 0.1 mm resolution.

If the client has the vector file, ask for it. That one email saves an hour of cleanup.

Relief or extruded text?

There are two ways to turn art into material, and they suit different things:

Method What it does Best for
Heightmap relief Every pixel becomes a height; bright stays low and dark rises (or the reverse) Multi-tone art, badges, image-plus-text plates
Extruded outline The outline is traced and pushed straight up into a solid wall Logos, lettering, icons, sign shapes

For a logo in two colours, extrusion wins: the walls are vertical, the top is flat, and the silhouette is exact. For something more like an engraved plaque where the art has shading, a heightmap relief is closer to what you want.

Lettering has its own page: text to STL extrudes real glyphs rather than tracing pixels, so a 3 mm stem stays 3 mm wide.

The numbers that decide whether it prints

  • Minimum stem width: about 0.8 mm. That is two extrusion widths on a 0.4 mm nozzle. Anything thinner either gets skipped or prints as a broken line.
  • Minimum gap between strokes: about 0.6 mm. Closer than that and the walls touch, and an "e" turns into a blob.
  • Text height: 8–10 mm minimum. Below that, most fonts lose their counters at printable scale.
  • Relief height: 1.5–3 mm for a plaque, 2–4 mm for a badge you want to feel.
  • Base plate: 0.8–1.2 mm. Thin bases warp; thick ones look heavy and waste time.
  • Handled size: 6 mm of stem at 10 mm text height if a logo is going on a keyring.

Three problems that catch almost everyone

Transparent PNGs come out as a black block. Many converters read transparency as zero, which is black, which becomes maximum height. The fix is to flatten the image onto a white background before converting — PNG to STL handles alpha explicitly so the transparent area becomes the base rather than raised material.

Thin strokes disappear. Look at your logo at the size it will print on paper. If a line is thinner than a pencil stroke at 30 mm wide, it will break in plastic. Either bump the minimum stroke weight in your vector editor or print bigger.

Black on white becomes inverted. Relief mode raises dark pixels. For a dark logo on a white background that gives you the logo standing proud — which is usually what you want. For text inside a filled block, it does the opposite, and you get the background raised instead. The invert switch exists for exactly this case; check the preview before you download.

A workflow that works

  1. Open the source in your browser and check the alpha or background is right.
  2. Convert at the real print width — a 60 mm keyring needs different settings from a 200 mm sign.
  3. Set the base plate around 1 mm and the relief to 2 mm.
  4. Load the STL into the viewer and look at it from the side: the outline should be sharp and closed.
  5. Slice with 0.12–0.16 mm layers, 2–3 walls, 15–20% infill.

If you want two colours, add a colour change at the height where the letters start. The whole base prints in one colour, the lettering in another — no painting, no purge tower needed beyond one change.

What not to expect

This is not a vectoriser. A low-resolution JPG will not become a sharp logo just because it went through an STL converter — garbage in, slightly three-dimensional garbage out. Fix the source first; the conversion takes seconds and is the easy part.

Questions

Common questions

What source file should I use for a logo?

SVG, by a wide margin. Vector edges are mathematically exact, so the STL comes out with vertical walls and crisp corners. A JPG screenshot of the same logo carries compression halos that become real geometry.

How thin can lettering be and still print?

About 0.8 mm with a 0.4 mm nozzle — two extrusion widths. Thinner strokes either break or disappear, so thicken the line in a vector editor or print the logo larger.

Why does my transparent PNG come out as a black block?

The converter is reading the transparent area as black, which becomes full height. Flatten the image onto white first, or use the invert switch after checking the preview.

What settings should I use for a printed sign?

For flat art, height 2–3 mm on a 1 mm base, with 0.12–0.16 mm layers and 2–3 walls. Text below 8–10 mm tall loses its counters no matter what settings you use.

Can I print a two-colour logo?

Yes: add a colour change at the layer where the raised lettering starts. The base prints in one colour and the letters in another, with no painting and only one filament swap.