Image to STL Online

How to Make a Lithophane From a Photo (Free, No Upload)

A lithophane hides a photo in the thickness of plastic: turn an image into an STL in the browser, then print it with settings that make the face recognisable.

A lithophane is a 3D print that only shows its picture when light passes through it. The photo lives in the plastic as thickness: thin material lets light through and reads as a bright area, thick material blocks it and reads as shadow. There is no ink and no colour — the printer is drawing a brightness map in white filament.

That is also why a first attempt often disappoints. The conversion takes a minute; thickness, layer height and the lamp behind the print decide whether anyone recognises the face in it.

Step 1: pick a photo that survives the conversion

A lithophane is a greyscale thickness map, so what matters is tonal separation, not colour.

Good candidates:

  • Strong contrast — the subject separates clearly from the background.
  • Soft, even light — overcast daylight or window light beats on-camera flash, which blows highlights into flat white.
  • A clean background — busy foliage or a cluttered room turns into grey mush at 3 mm of thickness.

Weak candidates: dim indoor shots, a dark subject against a dark background, and anything where the face occupies a small part of the frame.

A one-minute test: convert the photo to black and white and shrink it to thumbnail size. If you can still tell who it is, it will work. If it turns to mud, no slicer setting will rescue it.

Step 2: convert the photo in the browser

  1. Open the lithophane maker.
  2. Drop in a JPG, PNG or WebP file.
  3. Choose lithophane mode, so dark pixels become thick.
  4. Set the width (100 mm is a good default for a single portrait), the base thickness and the relief height.
  5. Download the STL.

The conversion happens on your machine: the image is decoded and turned into triangles by your browser and never uploaded. That matters for family photos, client logos and anything under an NDA.

Total thickness is the most important number here. 2.5–4 mm is the usable window. Under 2.5 mm the panel is fragile and washes out; over 4 mm it goes muddy because too little light gets through the dark areas.

If your source is already a height map — terrain data, a depth render, a scanned relief — use heightmap to STL instead. It skips the photo-specific tonal curve.

Step 3: print settings that work

Setting Value Why
Infill 100% any internal gap becomes a bright spot that is not in the photo
Layer height 0.12 mm or finer layer lines are the detail; 0.2 mm smears faces
Walls 2–3, or all walls you want solid material through the whole thickness
Orientation standing up, long edge on the bed layers run parallel to the image, which is where resolution comes from
Speed 30–40 mm/s rushing causes under-extrusion, which shows as banding
Supports none a standing rectangle does not need them
Filament white or natural PLA pigment blocks light; dark colours print flat and dim

A 100 × 150 mm panel at 0.12 mm layers takes roughly 4–8 hours. Almost all of that time is the layer height, not the model.

Step 4: get the light right

A lithophane in a dim room is a grey rectangle. Distance, diffusion and colour temperature do more for the result than any slicer setting:

  • Distance — 10–30 mm behind the print. Closer and only the centre glows; further and the image washes out.
  • Diffusion — an LED strip behind white acrylic or baking paper, never a bare LED. Point sources show as hot spots.
  • Colour temperature — 2700–3000 K flatters portraits; 5000 K and above looks clinical but reveals more detail.

The cheapest build that works: an LED strip inside a small picture frame, the print mounted in the frame opening, a diffuser sheet between them. The lithophane night light guide has the measurements.

Common failures and what causes them

Symptom Cause Fix
Washed out, no detail panel too thin, or the source photo is overexposed add thickness, darken the source before converting
Almost black too thick, or the filament is not white back to 2.5–3 mm, switch to white PLA
Horizontal bands under-extrusion at speed slow to 30 mm/s, check the extrusion multiplier
Features look melted print too small for the detail, or a low-resolution photo print bigger, start from a sharper file
Cracks when handled thin walls 3 mm minimum, two walls, glue into a frame

Where to go next

Once one print reads clearly under a lamp, the settings stop being mysterious. After that the useful experiments are size (bigger shows more), thickness (a wider range of tones) and backlighting. If you are unsure which mode to use, heightmap vs lithophane explains which brightness becomes thick and why.

Questions

Common questions

What file format should I start from?

JPG or PNG. PNG avoids JPEG compression artefacts in smooth gradients such as skies and skin. WebP works too; HEIC from a phone needs exporting to JPEG first.

Can I make a lithophane from a screenshot?

Yes if it has contrast. Portraits and landscapes work; text-heavy screenshots rarely do, because thin dark lines disappear at 0.12 mm layers.

Do I need a special nozzle?

No. A standard 0.4 mm nozzle prints lithophanes well. A 0.2 mm nozzle buys a little more detail at the cost of much longer print times.

Can I print the panel flat instead of standing up?

You can, but detail drops sharply: the layer lines then run parallel to the direction you look through the print, so the image becomes banded and soft.

Is the converter really free?

Yes. The conversion runs in your browser with no account, no credit limit and no watermark on the STL.